If there is no open coax jack, disconnect a coax cable from a nearby TV set-top box or cable gateway, and connect that coax cable to the Network connector of the MoCA Adapter. This end is near your router or the device connecting to your router.Īttach the included coax cable between the Network connector of the MoCA Adapter and an open coax jack if one’s available. In that case you will want to find the other end of 2 cables, the one near the router and the one near the device to be connected to the router.īring a MoCA adapter to one end of the cable you’re checking. This section is helpful if you don’t have a MoCA-ready network, and you hope to connect a router to another device through a MoCA-ready Sub-network. Most people don’t need to read this section. This can be useful if you don’t have a MoCA-ready network, and want to create a MoCA-ready Sub-network. Please see Finding The Other End Of A Coax Cable if, for instance, you need to find the other end of a coax cable that’s near your router. Note that these use splitters whose upper frequency is 1,000 MHz or higher. You can see that it’s possible to work around a network that’s not fully MoCA-ready as long as you have a MoCA-ready Sub-network like the ones below. However, if the root splitter only goes up to 900 MHz, the Router will probably not be able to use MoCA to connect to TV set 3. This is true even if the root splitter only goes up to 900 MHz, for instance. Note that in the home network diagram above, the Cable Modem/Router should be able to use MoCA to connect to TV 1 and Game Station as long as splitters 1 and 2 both go up to 1,000 MHz or above. This can help improve performance, but is often not necessary. If possible, terminate any open splitter coax output with a Coax Terminator.If that’s not possible, it should be okay if you have a MoCA-ready Sub-network as discussed below. If there’s more than one layer of branch splitters on your network side of the root splitter, correct that if possible.If a splitter doesn’t go up to 1,000 MHz, replace it with one that goes up to 1,000 MHz and preferably higher.Replace any amplified splitter with a splitter that isn’t amplified and whose upper frequency is at least 1,000 MHz, preferably higher.If some of these conditions are not true, you can probably still use MoCA. This means that you can do a simple installation as described in the Quick Start. If all these conditions are true, you have a MoCA-ready Network. You are not using your coax cable for DirecTV or some other satellite service, or for AT&T U-Verse.The maximum cable distance supported between the root splitter and the farthest cable outlet is 100 yards (90 meters).Normally you can replace an amplified splitter with one that’s not amplified, ideally using a splitter that goes up to at least 1,500 MHz. An amplified splitter will cause a problem. Note that some splitters are amplified, but most are not. There is no one-way amplifier or amplified splitter on your network’s side of your root splitter.(Sometimes an upper frequency of 900 MHz works, but often it does not.) Your splitters all have a frequency range that goes up to 1,000 MHz or above, ideally higher.It would not be true if two devices were connected to splitter 1. There is at most one layer of branch splitters on your network side of the root splitter.You can use MoCA for any or all of the devices shown in the picture if the following are all true: A cable comes into the home from a “drop” outside and goes to a “root splitter.” One or more cables branch out from the root splitter to all the devices in the home, in some cases going through additional splitters. In this example you can see that the coax network connects to a cable modem/router and three TVs. Details below are useful for the unusual cases where the MoCA Adapter installation was unsuccessful.īelow is a diagram of one possible coax network in a home. Most people who use MoCA Adapters can do a simple installation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |